CFS Carpet Trouble-Shooter

Domestic Carpet

COLOUR MATCHING – Carpets are produced in batches, known as creels, and usually each batch produces between 500 Sqm – 3000 Sqm in a single width, depending on the creel size. Whilst the recipe used by the dyer remains constant, and is followed to the letter, in each separate production the colour reproduction will vary from batch to batch. However production is matched back to the original or master sample to ensure that the colour remains ‘within a commercial tolerance’.

This process is not an exact science and a commercial tolerance is subjective, but nevertheless is usually the professional judgement of the head dyer based on his/her experience.

A greater level of tolerance is required on blended colours (heathers etc). To ensure perfect colour matching it is advisable that a single width be used in any installation requiring exact colour matching.

SAMPLES – All carpet & flooring samples held by individual retailers may not be from the same batch as current production and therefore should be used as a guide and not an exact colour match.

SHEDDING – All cut pile carpets will lose short fibre, which is created during production when spun yarn is cut for tuft formation. These fibres fall onto the surface of the pile and appear as ‘fluff’.

The effect varies with yarn type and may be removed without detrimental effect upon the carpet by vacuum cleaning. This excess fibre is only a small fraction of the total fibre contained in the carpet.

PULLED LOOPS – Pulled loops occur only in looped pile carpet where one or more loops in the continuous pile is pulled through the primary backing of the carpet. This is usually due to some local condition, possibly some sharp object which has caught in a loop in situ and has resulted in a pull. Pulled loops are easily dealt with by trimming the offending end level with the rest of the pile. They should NOT be lest as this could result in further loops being pulled and developing into a ladder.

SPROUTING – Occasionally an odd tuft or two can work its way to the surface and stand proud of the rest of the pile. This is probably due to one end of the tuft being longer than the other i.e J shaped tuft instead of V shaped. Remedial action merely requires that the offending tufts be scissor trimmed level with the rest of the pile. They should never be pulled out.

SHADING – Shading occurs because the pile of the carpet has become crushed, flattened or brushed in a different direction to the natural lie of the pile whilst in situ. This causes light reflection at differing angles resulting in the creation of light and dark patched on the carpet. This will occur on all pile fabrics but can be more noticeable on plainer carpets because the shadows created by pile pressure will not be disguised by a heavy pattern or design.

STATIC – Carpets do not produce static but like other household fabrics and objects have the capacity to store it. Static is caused by the build up of static electricity upon personnel in a dry environment and is discharged when a person makes contact with an object which can conduct electricity (i.e door handle or filing cabinets etc).

The static charges will carry in intensity depending upon the individual, air humidity and the contract materials. Static is more usually associated with synthetic materials as they do not retain moisture very well but it can and does occur with wools in very dry room conditions.

Preventative measures include the introduction of moisture into the room or in situ carpet treatment.

FADING ON WOOL – Carpets made from wool can and do fade in use. The degree of fade can vary depending on the colours chosen and the local conditions to which the carpet is subjected.

Fading can be caused by exposure to ultra violet light which is found in daylight, but is accelerated when sunlight shines directly onto the carpet. This has the effect of lightening or ‘bleaching’ the colour just as exposure to sunlight will lighten human hair. Wool is after all animal hair.

Protection should be given to carpets exposed to such conditions just as you would protect other furniture or fabrics.

A complaint on fading would be considered justified if it failed to meet the required shade standard when tested to the British Standard BS1006 (1990).

PILE REVERSAL (see shading) – Like shading, this occurs when the pie or nap of the carpet changed direction and thus reflects light at different angles showing the effects of shading which can become permanent. It is also described as ‘watermarking’. This can happen to every carpet construction and like shading it can be more apparent on plain carpet. It can occur quite quickly after installation. A tremendous amount of research has been carried out over many years by many institutes to determine the cause of this phenomenon but none of it has proved conclusive. There is no commonly known manufacturing process which can cause or cure this phenomenon and therefore it is not a manufacturing fault.

FLATTENING – Flattening will occur as a result of traffic which eventually flattens the pile particularly in the main areas of use. All pile fabrics will flatten to greater or lesser degree dependant on the amount of traffic to which it is subjected and the construction (tuft, density/ pile, fibre / height/ weight) of the product concerned.

INDENTATIONS – When carpet is subjected to a heavy point load, such as under the legs of furniture, it is unreasonable not to expect the carpet not to indent. Usually, the longer the load is in place, the longer the pile will take to recover. In the case of very heavy loads in place for a considerable time, the recovery time can be very considerable.

It must be remembered that it is not only the pile of the carpet that becomes indented, the underlay will also indent and the backing of the carpet may also distort into the indentation in the underlay. Some underlays will recover well and some less well depending upon their composition, thickness, density etc.

The use of cups below furniture legs can spread the loads and the net result is a larger area of less deeply indented carpet.

The ability of a carpet to recover from a heavy static load can be measured in the laboratory, using the test method described in BS 4939 and many manufacturers will have data on this aspect of carpet performance. In this test the carpet is loaded for 24 hours and the degree of recovery is measured after 1 hour and 24 hours. Since there are so many different underlay’s however, it is very rare for the recovery from a heavy static load to be evaluated on carpet underlay.

Often normal maintenance (vacuum cleaning with a rotating brush machine) will speed up recovery but in the case of serious indentation the use of an iron and damp cloth or steam iron together with a blunt darning needle to carefully tease up the pile can be beneficial. Care must be taken not to over wet the carpet of course.

SOILING – Soiling is usually the result of some local condition to which the carpet has been subjected to, or maintenance, or lack of maintenance programme. There is nothing we can do to prevent soiling in use. There are several types of soiling which are quite common:

Spillages – Liquids such as soft drinks, cordials or any drink which contains sugar particularly hot drinks, are likely to leave a stain. In such instances, professional help should be sought.

Shampoo – If incorrectly applied, can leave sticky soap residues in the fibres which can result in soiling reappearing quite rapidly.

Dust – Which is carried on draughts can soil carpets in various ways, apart from the obvious soiled edges, at gaping skirting boards for instance, dark lines appearing on surface might suggest airbornes dust-vacuum-drawn through poorly fitted floorboards. Sometimes the shape of floorboards can be seen quite clearly. Airborne dust sometimes shows itself as spots on the carpet, this is due to the air carried on the draught under the carpet escaping through minute holes both in the underlay and the carpet leaving dust deposited on the pile much like a filter action. In such installations, the use of a lining paper is essential as a preventative measure.

It is the responsibility of the retailer to advise the consumer when the carpet is measured of any poorly fitting doors, skirtings or floorboards and the consumers responsibility to ensure any remedial work to seal draughts, is carried out before the carpet is fitted, if a resulting complaint is to be avoided.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s